Wilderness Energy

Trike Hub Motor Kit

On Sale
THIS KIT REMOVES THE RACK AND ADDS THE EXTENDED RECUMBENT CABLE. SINCE MOST TRIKES COME WITH A BASKET, THERE IS NO NEED FOR THE RACK. YOU WILL NEED MORE CABLE LENGTH TO REACH THE MOTOR.

36 Volts, 600 watts with 50 amp controller unit, lighted thumb throttle, 36V 2 amp Soneil smart charger, 36 volt extended range battery pack (12 amp/hr batteries X 3) **Includeds 6 month warranty on all parts except batteries** --- DETERMINING WHEEL SIZES: to find the correct size wheel needed for your bicycle, DO NOT measure your wheel. Instead check the TIRE on your bicycle for the correct size. It should be molded or printed along the tire itself, and should read something like: 26 X 1.75 This means that your bike has 26 inch wheels, and that the tire is 1.75 inches wide.

Kit Installation Instructions

Important note: Never power up the motor before it is ins talled in your bike forks and the nuts are tightened firmly! If you spin the motor without the spindle being secured, you will wrap the cables up into a ball, severing wires and voiding you warrantee

S TE P 1 INS TALL WHE E L/HUB MOTOR

a) Remove old front wheel. (You may need to disconnect front brakes .)

b) Install a new tube and tire onto Hub Motor/Wheel. (You can use the set off your old wheel.)

c) Inflate Hub Motor/Wheel/Tire.

d) Check front fork inside distance. Should be a minimum of 3 3/4". Spread forks to meet this

distance if necessary.

e) Install new Hub Motor/Wheel/Tire onto bike forks . IMPORTANT! If your Kit is a BrushLESS system (B-36),

the motor cable must come out the LEFT s ide (when sitting on your bike seat and looking forward.) If you have

a Brushed system, the cable should come out the right side....

f) Make sure to TIGHTEN THE NUTS COMPLE TELY or wheel could spin in the front forks and sever your motor cable!

g) Reconnect brakes and adjust them so wheel spins freely.

S TE P 2 INSTALL THROTTLE

a) Remove old handlebar grip. (Tip: use lubricant - loosen brake lever

and use it to push handlebar grip off if necessary.)

b) Slide Throttle (thumb or twist grip) (handlebar should measure 7/8" outs ide diameter onto handlebar. - unpainted.)

c) Align markings on throttle as desired and tighten the allen screw.

S TEP 5 INSTALL BIKE RACK

a) Remove seat and securing bolt from seat post mounting.

b) Slip securing bolt through rack and back though seat post mounting.

c) Replace seat, adjust height as desired and tighten securing bolt.

d) Remove nuts from rear wheel center bolt and install

lower rear of bike rack onto protruding bolt at rear wheel bearing.

e) Replace nuts and re-tightenthem.

STE P 4 INS TALL CONTROLLER UNIT

a) Secure controller unit on the bike rack just under the seat.

or on the center verticle rail us ing 2 black zip ties wrapped around the rack,

then through the slot holes in the base of the controller.

S TE P 5 PLUG IN AND SECURE CABLES

a) Plug the cable coming from the throttle (small 4-wire cable) into the contoller unit, the cable coming from the

motor (cable with 3 power supplywires ) into the 4 ft. 3-plug cable coming from the controller.

(all plugs are idiot-proofed - you can't plug them in the wrong way!) DO NOT plug the battery cable into the controller yet!

c) Secure wires to the bike at their plug-in junction points with the zip ties .

b) Zip tie cables up from front wheel along front forks, then along the center frame rail up to the point where the controller unit is mounted.

STEP 6 INSTALL BATTERY PACK

a) Undo velcrow straps from battery pack bag. Weave them through the rack

framing and re-attatch.

b) Make sure the keyswitch is in the "Off" position, then plug battery pack 2-plug cable into controller.

Note: ALWAYS turn the keyswitch to the "Off" pos ition before plugging or unplugging the battery pack!

**BATTERY CARE ** Always charge your battery pack after EVERY use. Lead acid batteries hate to be dischaged, and if you run them out and then leave them uncharged for even a few days - they will be destroyed. Plug them in after ever use and they'll last for years !!!

HAPPYE -MOTORING!!